Product Guides November 8, 2026

Types of Gland Packing: Selection Chart for Pumps, Valves and Steam

Types of gland packing: graphite, PTFE, aramid and hybrid packing samples


Choosing gland packing starts with three questions: what is the media, how hot is it, and is the shaft rotating, reciprocating or a valve stem? This guide sorts our 29 types of gland packing by material and shows the temperature, pressure, speed and pH limits of each one, with the pumps, valves and industries it suits best. Use the selection chart below to shortlist two or three styles, then check the detail tables.

Gland Packing Selection Chart by Application

Start here if you know the application. Each style links to its product page with full specifications.

ApplicationRecommended styles
Steam and high-temperature valvesFS-P308I, FS-P308S, FS-P305I, FS-P305S, FS-P302
Corrosive chemical pumps and valvesFS-P103, FS-P103S, FS-P106, FS-P404
Slurry, ash and abrasive mediaFS-P203, FS-P203S, FS-P207, FS-P403
Pulp and paperFS-P209, FS-P406, FS-P502
Water, wastewater and general pumpsFS-P403, FS-P405, FS-P206, FS-P601
Hot oil and heat transfer systemsFS-P302, FS-P308S, FS-P505
Cold water, irrigation and marineFS-P801, FS-P802, FS-P802G
Furnace doors and hot gas (static)FS-P701, FS-P702

How to Read the Technical Data

  • Temperature is the service limit of the packing. Graphite values marked “steam” apply in steam; in air graphite oxidizes above about 450 °C.
  • Rotary pressure and speed apply to centrifugal pumps, mixers and agitators. Reciprocating pressure applies to plunger and piston pumps. Static / valve pressure applies to valve stems and static joints.
  • pH is the chemical range the packing tolerates. Strong oxidizers need a separate check.
  • Not all maximum values can be used at the same time. Higher shaft speed creates more frictional heat, so the allowable pressure and temperature drop.

📄 Download the full Gland Packing Technical Parameters chart (PDF, A3) – all 29 styles on one page.

Graphite Gland Packing for Valves and Steam

Flexible graphite does not melt or harden in service, and it conducts frictional heat away from the stem. That makes graphite packing the first choice for steam, hot oil and high-temperature valves. Metal-wire cores and jackets add extrusion resistance for high-pressure valves; pure graphite stays softer for slow-moving pumps.

ImageStyleKey dataBest for
FS-P302 Graphite Gland PackingFS-P302
Graphite Gland Packing
Temp. ≤ 450 °C
Rotary 30 bar / 20 m/s
Static / valve 200 bar
pH 0–14
Valve stems and slow-speed pumps on steam, hot oil and hot water in power plants, refineries and steel mills.
FS-P305I Inconel Core-Reinforced Graphite Gland PackingFS-P305I
Inconel Core-Reinforced Graphite Gland Packing
Temp. -200…+650 °C (steam; ≤ 450 in air)
Static / valve 300 bar
pH 0–14
High-pressure steam and hot-oil valves where pure graphite would extrude; Inconel core for the hottest service.
FS-P305S SS304 Core-Reinforced Graphite Gland PackingFS-P305S
SS304 Core-Reinforced Graphite Gland Packing
Temp. -200…+550 °C (steam; ≤ 450 in air)
Static / valve 300 bar
pH 0–14
The same valve duties as the Inconel-core version at a lower cost, with SS304 wire for moderate temperatures.
FS-P308I Inconel Wire Jacketed Graphite Gland PackingFS-P308I
Inconel Wire Jacketed Graphite Gland Packing
Temp. -200…+650 °C (steam; ≤ 450 in air)
Static / valve 500 bar
pH 0–14
Superheated and saturated steam valves, high-temperature oxidizing service and corrosive petrochemical lines; up to 500 bar static.
FS-P308S SS304 Wire Jacketed Graphite Gland PackingFS-P308S
SS304 Wire Jacketed Graphite Gland Packing
Temp. -200…+600 °C (steam; ≤ 450 in air)
Static / valve 500 bar
pH 0–14
High-pressure steam and hot-oil valves in power, refinery and chemical plants where Inconel is not required.

PTFE Gland Packing for Chemical Service

PTFE is inert to almost every chemical across pH 0–14, which makes it the default for corrosive pumps and valves. Virgin PTFE gives the best recovery and service life; PTFE filament is a cost-effective option for standard duty; silicone oil or graphite impregnation lowers friction for faster shafts.

ImageStyleKey dataBest for
FS-P103 PTFE Gland PackingFS-P103
PTFE Gland Packing
Temp. -100…+260 °C
Rotary 15 bar / 10 m/s
Reciprocating 100 bar
Static / valve 150 bar
pH 0–14
Pumps and valves on corrosive chemicals across the full pH 0–14 range; clean, oil-free and non-staining.
FS-P103S PTFE Gland Packing with Silicone OilFS-P103S
PTFE Gland Packing with Silicone Oil
Temp. ≤ 240 °C
Rotary 15 bar / 12 m/s
Reciprocating 100 bar
Static / valve 150 bar
pH 0–14
Centrifugal and reciprocating pumps and agitators on corrosive media, where silicone oil eases running-in.
FS-P105 PTFE Filament Gland PackingFS-P105
PTFE Filament Gland Packing
Temp. ≤ 240 °C
Rotary 12 bar / 10 m/s
Reciprocating 75 bar
Static / valve 80 bar
pH 0–14
Standard-duty pumps and valves on general chemicals and water treatment, at a lower price than virgin PTFE.
FS-P105S PTFE Filament Gland Packing with Silicone OilFS-P105S
PTFE Filament Gland Packing with Silicone Oil
Temp. ≤ 240 °C
Rotary 12 bar / 10 m/s
Reciprocating 75 bar
Static / valve 80 bar
pH 0–14
Standard-duty pumps, valves and agitators where lower running-in friction is needed at an economical price.
FS-P106 Graphite PTFE Gland PackingFS-P106
Graphite PTFE Gland Packing
Temp. ≤ 240 °C
Rotary 25 bar / 20 m/s
Reciprocating 150 bar
Static / valve 150 bar
pH 0–14
Rotary, reciprocating and plunger pumps on corrosive fluids at higher shaft speeds, up to 20 m/s.

Aramid and Synthetic Fiber Packing for Abrasive Service

Aramid fiber is very strong and wear resistant, so it holds up where slurry, ash or crystals would cut softer packings. Use a hardened shaft sleeve with para-aramid. Meta-aramid and spun aramid are gentler on the shaft; phenolic (novoloid) fiber is a heavy-duty choice for pulp and paper.

ImageStyleKey dataBest for
FS-P203 Aramid Fiber Gland PackingFS-P203
Aramid Fiber Gland Packing
Temp. -100…+240 °C
Rotary 30 bar / 10 m/s
Reciprocating 150 bar
Static / valve 200 bar
pH 4–11
Abrasive service: rotary pumps, mixers and valves handling ash, slurry, mud and gravel.
FS-P203S Aramid Gland Packing with Silicone CoreFS-P203S
Aramid Gland Packing with Silicone Core
Temp. -50…+200 °C
Rotary 30 bar / 10 m/s
Reciprocating 150 bar
Static / valve 200 bar
pH 4–11
High-vibration slurry and ash pumps, mixers, agitators and reactors with particle-laden media.
FS-P206 Meta-Aramid Gland Packing (Nomex-Style)FS-P206
Meta-Aramid Gland Packing (Nomex-Style)
Temp. -100…+220 °C
Rotary 25 bar / 10 m/s
Reciprocating 100 bar
Static / valve 200 bar
pH 4–10
Pumps and valves on water, sewage, steam, solvents and mild chemicals with mildly abrasive media.
FS-P207 Spun-Aramid Gland PackingFS-P207
Spun-Aramid Gland Packing
Temp. -100…+240 °C
Rotary 30 bar / 10 m/s
Reciprocating 150 bar
Static / valve 200 bar
pH 4–11
Rotary pumps, mixers and valves that need high strength without aggressive shaft wear.
FS-P209 Phenolic Fiber Gland PackingFS-P209
Phenolic Fiber Gland Packing
Temp. -50…+250 °C
Rotary 25 bar / 10 m/s
Static / valve 200 bar
pH 1–12
Pulp and paper: stock pumps, hydraulic beaters, refiners, plus wastewater treatment plants.

Hybrid and Corner-Reinforced Packing

Hybrid packings combine two yarns in one braid: PTFE or graphite PTFE for low friction and chemical resistance, aramid at the corners or interbraided for strength. They cover the widest range of pump duties with one style, which makes them popular stock items for distributors.

ImageStyleKey dataBest for
FS-P403 Graphite PTFE Gland Packing with Aramid CornerFS-P403
Graphite PTFE Gland Packing with Aramid Corner
Temp. -100…+240 °C
Rotary 35 bar / 15 m/s
Reciprocating 150 bar
Static / valve 150 bar
pH 2–12
Pumps, mixers and valves on water, oil, slurry and weak acids or alkalis, where low friction and wear resistance are both needed.
FS-P404 Aramid & Black PTFE Interbraided Gland PackingFS-P404
Aramid & Black PTFE Interbraided Gland Packing
Temp. -100…+260 °C
Rotary 35 bar / 15 m/s
Reciprocating 150 bar
Static / valve 200 bar
pH 2–12
Rotating pumps on hot water, salt solutions, most acids and alkalis, fuels, oils, solvents and suspended solids.
FS-P405 PTFE Gland Packing with Aramid CornerFS-P405
PTFE Gland Packing with Aramid Corner
Temp. -100…+240 °C
Rotary 35 bar / 12 m/s
Reciprocating 150 bar
Static / valve 150 bar
pH 2–12
Clean, light-colored alternative to FS-P403 for pumps and mixers on mildly abrasive water and chemical service.
FS-P406 Aramid & PTFE Interbraided Gland PackingFS-P406
Aramid & PTFE Interbraided Gland Packing
Temp. -100…+260 °C
Rotary 35 bar / 15 m/s
Reciprocating 150 bar
Static / valve 200 bar
pH 3–12
High-pressure reciprocating pumps and medium-speed centrifugal pumps; non-staining for pulp, paper, food and sugar processing.

Carbon Fiber and Pre-Oxidized Fiber Packing

Carbon-based fibers resist heat and most chemicals and do not shrink or harden. Pre-oxidized PAN fiber is the economical grade; fully carbonized fiber gives higher strength and temperature. Both are available with PTFE, graphite, or PTFE plus graphite impregnation. Avoid strong oxidizers.

ImageStyleKey dataBest for
FS-P502 Pre-Oxidized PAN Fiber PackingFS-P502
Pre-Oxidized PAN Fiber Packing
Temp. ≤ 260 / ≤ 300 °C (PTFE / graphite impregnation)
Rotary 30 bar / 15 m/s
Reciprocating 150 bar
Static / valve 250 bar
pH 1–13
Pumps and valves on steam, hot water, solvents and mild acids or alkalis in pulp and paper, wastewater and power plants.
FS-P505 Carbon Fiber PackingFS-P505
Carbon Fiber Packing
Temp. ≤ 260 / ≤ 450 °C (PTFE / graphite (air); higher in steam)
Rotary 30 bar / 15 m/s
Static / valve 300 bar
pH 1–13
Pumps, valves and agitators in power, chemical and steel plants; graphite grade for hotter steam and hot oil.

High-Temperature Static Packing

Ceramic fiber and glass fiber packings are non-combustible and made for static sealing and insulation at very high temperatures. They are not for pumps or valve stems.

ImageStyleKey dataBest for
FS-P701 Ceramic Fiber Gland PackingFS-P701
Ceramic Fiber Gland Packing
Temp. ≤ 1000 °C (fiberglass-reinforced: ≤ 550)
Static / valve 5 bar
pH 5–9
Long-term static sealing at very high temperature: furnace and kiln doors, hot-gas ducts and flue joints.
FS-P702 Glass Fiber PackingFS-P702
Glass Fiber Packing
T max ≤ 550 °C
Static sealing only
Oven and furnace doors, boiler hatches, flue dampers, stoves and hot-gas ducting; static only.

General-Service and Economy Packing

For cold water, irrigation, marine and other low-pressure duties, acrylic, cotton and ramie packings do the job at a lower cost. PTFE or graphite impregnation improves chemical resistance and lubrication.

ImageStyleKey dataBest for
FS-P704 PTFE-Impregnated Asbestos Gland PackingFS-P704
PTFE-Impregnated Asbestos Gland Packing
Temp. -100…+260 °C
Rotary 20 bar / 8 m/s
Static / valve 200 bar
pH 3–12
General-service water, steam, oil and weak chemical duties in legacy equipment, only in markets where asbestos is lawful.
FS-P601 PTFE-Impregnated Acrylic Fiber Gland PackingFS-P601
PTFE-Impregnated Acrylic Fiber Gland Packing
Temp. -50…+250 °C
Rotary 20 bar / 8 m/s
Static / valve 80 bar
pH 3–11
Pumps, valves, mixers and kneaders in chemical processing, paper making and water treatment.
FS-P601G Graphite-Impregnated Acrylic Fiber Gland PackingFS-P601G
Graphite-Impregnated Acrylic Fiber Gland Packing
Temp. ≤ 200 °C
Rotary 25 bar / 10 m/s
Reciprocating 75 bar
Static / valve 80 bar
pH 4–11
Pumps, valves and mixers in water treatment, paper making and general industry where a dark packing is acceptable.
FS-P801 Grease-Impregnated Cotton Fiber Gland PackingFS-P801
Grease-Impregnated Cotton Fiber Gland Packing
Temp. -20…+100 °C
Rotary 10 bar / 8 m/s
Reciprocating 50 bar
Static / valve 40 bar
pH 6–8
Cold water pumps, marine stern tubes and rudder stocks, irrigation pumps and low-pressure water valves.
FS-P802 PTFE-Impregnated Ramie Fiber Gland PackingFS-P802
PTFE-Impregnated Ramie Fiber Gland Packing
Temp. -40…+120 °C
Rotary 20 bar / 10 m/s
Reciprocating 50 bar
Static / valve 80 bar
pH 5–9
Low-pressure cold water pumps, irrigation equipment and general water valves where cost comes first.
FS-P802G Graphite-Impregnated Ramie Fiber Gland PackingFS-P802G
Graphite-Impregnated Ramie Fiber Gland Packing
Temp. -40…+150 °C
Rotary 20 bar / 10 m/s
Reciprocating 50 bar
Static / valve 80 bar
pH 4–12
Water, irrigation and drainage pumps and general water valves where a low-cost dark packing is acceptable.

How to Choose the Right Gland Packing in 5 Questions

  1. What is the media? Chemicals point to PTFE; abrasive slurry points to aramid; steam and hot oil point to graphite.
  2. What is the temperature? Above 260 °C, PTFE-based packings are out; use graphite or carbon fiber.
  3. What is the equipment? Valve stems need extrusion resistance (metal-wire graphite). Rotating pumps need low friction and heat dissipation. Reciprocating pumps need high pressure resistance.
  4. What are the shaft speed and pressure? Compare them with the rotary or reciprocating limits, and remember they cannot all be at maximum together.
  5. What is the shaft condition? Hard fibers like para-aramid need a hardened sleeve; on soft or worn shafts choose PTFE, graphite PTFE or spun aramid.

For more detail on specific families, read How to Choose the Right Graphite Packing, PTFE Packing vs PTFE Filament Packing and How to Tell Good Gland Packing from Bad.

Gland Packing FAQ

What are the main types of gland packing?

By material, the main types are graphite, PTFE, aramid, hybrid (PTFE or graphite PTFE with aramid), carbon fiber, mineral fiber such as ceramic and glass, and vegetable or acrylic fiber packing. Graphite suits steam and high temperature, PTFE suits chemicals, aramid suits abrasive media, and vegetable or acrylic fiber suits low-pressure water service.

Which gland packing is best for steam valves?

Graphite packing. For high-pressure steam valves, choose a metal-wire reinforced or wire-jacketed graphite packing such as FS-P308I or FS-P305I, which resists extrusion. Pure graphite FS-P302 suits lower pressures and slow-moving pumps.

What packing should I use for slurry pumps?

Aramid packing such as FS-P203, or FS-P203S with a silicone core for high-vibration pumps. For mixed abrasive and chemical service, FS-P403 graphite PTFE with aramid corners balances wear resistance and low friction. Use a hardened shaft sleeve with aramid packing.

Can I use all the maximum values at the same time?

No. Maximum pressure, speed and temperature are each tested on their own. In real service, higher speed means more frictional heat, so the safe pressure and temperature are lower. Send us your full operating data and we will check the combination.

What is the difference between PTFE packing and PTFE filament packing?

PTFE packing (FS-P103) is braided from yarn made of virgin PTFE film and has better recovery and service life. PTFE filament packing (FS-P105) uses thinner filament yarn and costs less, which suits standard-duty service.

Need Help Selecting Gland Packing?

Send us the media, temperature, pressure, shaft speed and stuffing box size. We will recommend the right style and quote within 24 hours. Factory-direct supply, sizes 3–40 mm, samples available.

📩 WhatsApp: +86 187 1010 7193
✉️ Email: sales@felixsealing.com
🌐 www.felixsealing.com